Fidamen

Convert kPa to PSI – Pressure Converter

This converter converts a single numeric value from kilopascals (kPa) to pounds per square inch (psi). The relationship is a fixed physical constant and the tool provides clear, traceable results for engineering, laboratory, and field use.

Use this tool for quick conversions, documentation of measurement reports, or when specifying pressure setpoints. For safety-critical or regulatory applications, follow calibration and uncertainty procedures described below and reference applicable standards.

Updated Nov 29, 2025QA PASS — golden 25 / edge 120Run golden-edge-2026-01-23

Governance

Record edf5353d2e35 • Reviewed by Fidamen Standards Committee

Interactive converter unavailable for this calculator.

We could not resolve compatible units for this experience. Please verify the slug follows the pattern `from-unit-to-unit-converter`.

Methodology

The conversion uses the internationally accepted exact relationship between the pascal and the pound-force per square inch. The calculator applies the standard constant so results are deterministic and repeatable.

When reporting converted values for compliance, include the rounding precision and an estimate of measurement uncertainty. For instrumentation and calibration guidance consult NIST and ISO standards listed in the citations. OSHA guidance covers safety and pressure-vessel regulations where applicable.

Key takeaways

This converter applies a fixed, exact mathematical relationship to convert kPa to psi. It is suitable for routine engineering conversions.

For compliance, safety, or metrology use include calibration traceability and uncertainty following NIST, ISO, IEEE, and OSHA guidance cited below.

Worked examples

Standard atmosphere: 101.325 kPa → 101.325 / 6.894757293168 = 14.6959488 psi (report as 14.696 psi for 6 significant digits).

Tire inflation example: 220 kPa → 220 × 0.14503773773 = 31.908301 psi (report as 31.91 psi for 4 significant digits).

Low pressure example: 10 kPa → 10 / 6.894757293168 = 1.450377377 psi (report as 1.450 psi if three decimals are needed).

F.A.Q.

Is this conversion for absolute or gauge pressure?

The mathematical conversion applies to any pressure value expressed in kPa. Whether that kPa value is absolute or gauge depends on how the measurement was taken. Label converted results as 'kPa (gauge)' or 'kPa (abs)' as appropriate before converting to psi.

How many decimal places should I report?

Choose decimal places based on the measurement instrument's resolution and required uncertainty. For safety-critical controls or regulatory reporting follow your organization or industry standard (often 2–3 significant figures for field gauges, more for laboratory instruments). Always state the rounding and uncertainty.

How accurate is the conversion constant?

The conversion uses the exact SI-derived relationship between pascals and pounds per square inch; the numeric constant shown is sufficient for practically all engineering and commercial uses. For metrology-grade work include instrument uncertainty and calibration traceability per NIST/ISO guidance.

Do I need to calibrate my pressure gauge before converting readings?

Yes. Calibrate pressure instruments regularly against a traceable standard. Conversion does not remove instrument bias or drift. Follow calibration intervals and procedures per ISO 17025, NIST traceability recommendations, and any applicable OSHA requirements for safety equipment.

Are there regulatory concerns when converting units for compliance documents?

Regulators may require both the original measurement unit and the converted unit, plus stated uncertainty and calibration traceability. Always check applicable standards and include references to calibration certificates when submitting reports.

Sources & citations

Further resources

Versioning & Change Control

Audit record (versions, QA runs, reviewer sign-off, and evidence).

Record ID: edf5353d2e35

What changed (latest)

v1.0.0 • 2025-11-29 • MINOR

Initial publication and governance baseline.

Why: Published with reviewed formulas, unit definitions, and UX controls.

Public QA status

PASS — golden 25 + edge 120

Last run: 2026-01-23 • Run: golden-edge-2026-01-23

Engine

v1.0.0

Data

Baseline (no external datasets)

Content

v1.0.0

UI

v1.0.0

Governance

Last updated: Nov 29, 2025

Reviewed by: Fidamen Standards Committee (Review board)

Credentials: Internal QA

Risk level: low

Reviewer profile (entity)

Fidamen Standards Committee

Review board

Internal QA

Entity ID: https://fidamen.com/reviewers/fidamen-standards-committee#person

Semantic versioning

  • MAJOR: Calculation outputs can change for the same inputs (formula, rounding policy, assumptions).
  • MINOR: New features or fields that do not change existing outputs for the same inputs.
  • PATCH: Bug fixes, copy edits, or accessibility changes that do not change intended outputs except for previously incorrect cases.

Review protocol

  • Verify formulas and unit definitions against primary standards or datasets.
  • Run golden-case regression suite and edge-case suite.
  • Record reviewer sign-off with credentials and scope.
  • Document assumptions, limitations, and jurisdiction applicability.

Assumptions & limitations

  • Uses exact unit definitions from the Fidamen conversion library.
  • Internal calculations use double precision; display rounding follows the unit's configured decimal places.
  • Not a substitute for calibrated instruments in regulated contexts.
  • Jurisdiction-specific rules may require official guidance.

Change log

v1.0.0 • 2025-11-29 • MINOR

Initial publication and governance baseline.

Why: Published with reviewed formulas, unit definitions, and UX controls.

Areas: engine, content, ui • Reviewer: Fidamen Standards Committee • Entry ID: e87b43d865fe